Tsunami by True Touch Floors

Brand new from True Touch Floors is our new Tsunami Collection. This 20mil WPC floor has an Embossed In-Register (EIR) finish; featuring three clean and contemporary visuals, that are 9” wide by 72” long, and it is now available in Florida!

Better yet, True Touch has partnered with the 4Ocean project to help remove plastic from the ocean, which helps protect sea-life, while cleaning up the environment. So far, over 40 million pounds of plastic has been pulled out of the ocean! It’s a staggering number to think about…

If you’re in the area, stop on by and see Peggy, Josh, Adam, and the crew at John Moore Flooring in Sun City Center, Florida. The company has a solid reputation, and they are known for their quality installations. As long time industry veterans, John Moore Flooring can help you with all your flooring needs. While you’re there, be sure to check out the Tsunami Collection, and help us clean the ocean and protect our environment for generations to com

Comments

Solid Vs. Engineered Hardwood. Which is better?

In this article I will cover the difference between engineered and solid wood flooring. I often get asked; is engineered hardwood actually real wood? The answer to that question is: Yes! There are some who think that engineered wood is inferior to its solid counterpart. Solid wood has its benefits, however it is not necessarily better than engineered. Actually, the opposite just may be true. Engineered hardwood has a cross-plywood construction, with a solid wood veneer laminated to the top. Solid hardwood is just that, solid. Both styles range in thickness from 5/16 to 3/4 inch. Both types of floors come prefinished or unfinished and come in a variety of widths and styles. There are several benefits to engineered hardwood. Here are just a few. Engineered hardwood is more dimensionally stable than solid wood flooring. Engineered floors can be glued down directly to concrete, floated or stapled. They can be installed above, on, or below grade. Engineered floors are less prone to cupping...

Urethane vs. Acrylic adhesives

If you are about to install engineered hardwood using the glue down method, I recommend that you read this article. One of the most important factors when installing engineered hardwood is the adhesive. Using the proper adhesive is critical to a successful installation. In this article I will briefly cover the differences between Acrylic and Urethane based adhesives. Let me start with acrylic adhesives. Acrylic adhesives are resin based and contain a certain percentage of water in them. The main problem with resin based adhesives, is the lack of tensile strength. In order for Acrylic adhesives to perform at their optimal level, the sub-floor needs to be well prepared and extremely flat. If the sub-floor is not level and flat and you choose to use an acrylic adhesive, I guarantee you will have hollow spots once the job is complete. Hollow spots are areas in which the wood floor is not adhered properly to the substrate. This problem is common and can be recognized by a popping or hollow ...

Hardwax Oil vs. Urethane Finishes

In the early to mid 1980's, a new type of urethane fini sh entered the market; water-base urethane was the new craze. With the entrance of water-base into the market-place, contractors quickly began to realize its value. The new water-base finishes added extra durability, dried much faster than its counterpart, and reduced the amount of labor hours. Prior to urethane finishes, hardwood floors were often sealed with multiple layers of shellac (lacquer was also popular); contractors would apply a coat of hot wax, which acted as a protective barrier. Finally, contractors would then polish the floor; finishing it up. Now, almost after a half of a century, the new craze is here; "Hardwax Oil". Made from waxes and oils, such as carnauba and parrafin wax, and natural oils, such as sunflower and linseed. Hardwax Oil is quickly gaining favor in the hardwood finish industry. So, the question is, which is better. Urethane or Hardwax Oil?...

The-Floor-Man.Blogspot

Search This Blog